Propex Heatsource HS2800 Heater Unit + Single Outlet Vehicle Kit
Propex Heatsource blown air systems are used in many applications throughout the world, these include Motorhomes, Caravans, Boats, Cranes, Horseboxes and Mobile Workshops etc. Both 12 and 24 volt versions are available.
Both the HS2000 and HS2800 are supplied as standard with a solid state electronic thermostat which automatically switches the unit on and off to maintain the desired temperature. When the room temperature drops below the selected level, the Heatsource will automatically ignite and run until the cabin reaches the selected temperature. The thermostat is an easy to fit surface mount design and integrates with the new electronics fitted to the HS2000 and HS2800 heaters. An easy to operate panel mounted digital timer/thermostat specifically designed for heatsource, is also available. Unlike some heaters, there is minimal electric current consumption during ignition so cycling the heatsource on and off does not have the effect of additional battery drain.
With forced air combustion and the Propex two stage stainless steel heat-exchanger, the HS2000 and HS2800 are a clean and highly efficient way to heat your vehicle or boat. Air for combustion is taken from outside and passed into the combustion chamber having been mixed with gas during three aeration stages, it is ignited automatically and heats up the large surface area of the heat-exchanger. The Heatsource units are totally room sealed and exhaust all products of combustion externally through the neat 22mm i.d. stainless steels flue pipe. To add to the efficiency, cabin air is normally re-circulated in preference to using cold air from outside. The HS series heaters are also very efficient on electrical current consumption, the high quality motor/fan combination and innovative current reducing electronics, both of which have been improved in the latest versions, means that even the larger HS2800 draws less than 2 amps during normal operation.
Propex heaters are designed to be quiet in operation without compromising air throughput and heat output. There will always be some air noise from a system that produces a healthy throughput of air, however, by using high quality balanced fans and smooth enclosed motors with ball race bearings, noise is kept to a minimum. Noise is also unaffected by high voltage, a common occurrence with battery charges, solar panels etc permanently wired. The micro-processor electronics regulates the motor voltage so that the fan speed does not alter from 10 to 15 volts.
Heatsource blown air heaters conform to the latest European standards for both the appliance and the electronics and during the rigorous testing the focus is very much on safety. The heaters also have to comply with an enhanced version of the Electro Mechanical Compatibility Directive to ensure they do not interfere with other electronics and that they are immune from interference by other electronics. The intelligent electronics are continuously monitoring the operation of the heater to make sure everything is operating correctly and safely. This includes monitoring of the flame, case temperature, combustion airflow, gas solenoid valve and voltage. Should any of these stray outside of the predetermined levels, the heater will be switched off and the red light on the thermostat will indicate a fault by flashing a certain number of times.
Both the HS2000 and HS2800 are supplied with complete fitting kits to suit vehicle applications. In vehicles and caravans the unit is usually mounted in a bed-box or cupboard, flue downwards through the floor and out to the side of the vehicle using flexible stainless ducting. These ducts (22mm i.d. for the HS2000 and 26mm i.d. for the HS2800) are supplied as standard in lengths of 750mm for vehicles. The ends are finished with neat stainless steel end-caps which comply with EN624. The heat is ducted to one or more outlets through tough highly flexible 60mm or 76mm ducting. In the case of multi-outlet installations, the first outlet is an open outlet with directional control and the rest are closable and are used in conjunction with the appropriate sized plastic Y branches.
The Propex HS2800 is an automatic thermostatically controlled blown air heating system fuelled by propane or gas. Heatsource is designed for a variety of automotive and marine aplications as a source of heat totally independant of the engine.
- Runs on clean burning propane or butane gas
- Quiet thermostatic operation
- Stainless steel burner and heat exchanger with clean combustion gives maintenance free durability
- Low electrical current consumption
- Compact and easy to install
- Fast warm-up time
- Reduces condensation
- High quality motor with ball race bearings
- Advanced micro-processor electronics
- Self diagnostic fault finding system
- Fully CE compliant and tested to the latest European standards
A single outlet single kit (V1) contains
- 1 x 1 metre 76mm ducting
- 1 x 1 metre 26mm combustion inlet pipe
- 1 x 0.75 metre 26mm Stainless Steel Exhaust pipe
- 1 x Thermostat
- 3.5 metres thermostat wiring harness
- 3.5 metres 12v supply harness
- 1 x directional hot air outlet
- 1 x directional cool air return vent
- Hose clips, fasteners, screws, inline fuse, instructions, drilling template
Available with twin dial or digital control panel, please select upon ordering.